Whole-home repipe in PEX-A or copper to replace failing galvanized, polybutylene, or pinhole-prone copper. Permits handled, walls patched, and everything pressure-tested and inspected.
Repiping is one part of our plumbing installation coverage in Indiana. For the full picture — symptoms, costs, and when to repair vs. replace — start with the complete Plumbing Installation guide, or browse every plumbing installation service we offer.
A whole-home repipe is the permanent fix for a house whose supply pipes have reached end-of-life — original galvanized steel closing up and rusting the water, polybutylene from the 1980s–90s failing without warning at the fittings, or copper that keeps developing pinhole leaks on run after run. Instead of chasing one leak at a time inside the walls, a repipe replaces the entire supply distribution in one planned project, restores full pressure to every fixture, and resets the clock on the most failure-prone system in the house.
We repipe in PEX-A and type-L copper. PEX-A is flexible, freeze-tolerant, corrosion-proof, and fast to route with fewer fittings inside the walls, which means fewer potential leak points and a lower cost; type-L copper is rigid, time-proven, and preferred where exposed runs, high heat, or local code call for it. Our plumbers map the runs, open the minimum number of access points, pull the new lines, tie in every fixture, and pressure-test the whole system before anything is closed.
Repiping is turn-key: free on-site consultation, a written quote good for 30 days, permits pulled and the municipal inspection scheduled, drywall access points patched and textured, and the water restored the same day in most single-story homes. Financing is available through Synchrony at 0% APR for the first 12 months on projects over $1,500, and the work carries a 10-year workmanship guarantee on top of the pipe manufacturer's warranty.
Different job? Start on the right page:
Pipe Replacement — if only one section or branch needs replacing.
Watch for these repiping warning signs
Rusty or discolored water
Brown water at the first draw, or a metallic taste, means galvanized pipe is corroding from the inside. When it's happening at multiple fixtures, the whole distribution is due.
A copper system that leaks a pinhole, gets patched, then leaks another one on a different run within months has aggressive water eating it everywhere. Patching becomes a losing game — a repipe ends it.
Weak pressure throughout the house
When every fixture runs weak, not just one, the supply pipe has narrowed from the inside across the whole home. New full-bore pipe restores the pressure the fixtures were designed for.
Polybutylene pipe anywhere in the home
Gray polybutylene supply pipe becomes brittle and fails at the fittings unpredictably. Insurers often won't cover it, and a proactive repipe removes the liability before it lets go.
Home built before 1975
Homes from before the mid-1970s often still run original galvanized steel well past its 50-year life. If it's never been repiped, the pipe is living on borrowed time.
Common causes, straight fixes
Galvanized steel at end-of-life
Galvanized pipe corrodes and closes from the inside over decades until flow drops and the water rusts. There's no reversing it — the material has simply reached the end of its service life.
Polybutylene brittleness
Poly pipe and its acetal fittings degrade with exposure to chlorinated water and become brittle, failing at the joints without warning. Whole-home replacement is the only reliable fix.
Aggressive-water copper pitting
Acidic or high-velocity water pits copper from the inside until pinholes weep through, clustering on hot and recirculation lines. When it recurs across runs, the system is the problem.
Hard-water and coastal corrosion
Mineral scale narrows pipe from the inside while coastal salt air corrodes it from the outside, and both accelerate a supply system toward whole-home failure.
Undersized original distribution
Homes plumbed with undersized trunk lines never delivered proper pressure to simultaneous fixtures. A repipe is the chance to correct the sizing, not just replace the pipe.
What happens when you call
1
Call or schedule online. Pick a 2-hour window for repiping in Indiana, by phone or online. Within five minutes you get a confirmation carrying the assigned tech's name and photo.
2
We diagnose on-site. On arrival we diagnose the repiping on-site — free for most repairs, $39 on minor service calls (waived if you proceed). You see the issue and the fix before we start.
3
Flat-rate quote. Before work begins, the repiping price is fixed in writing and holds for 30 days; no hourly creep, no surprise add-ons.
4
Done the same visit. The truck arrives stocked with the common valves, fittings, cartridges, and fixtures, so repiping usually finishes in a single visit.
What does repiping cost in Indiana?
Repiping in Indiana starts at from $1,499, every repiping quote is flat-rate and presented in writing before work begins — no surprise add-ons, no hourly creep. Seniors (65+) and military save 10% on labor, and financing covers projects over $1,500 at 0% APR for 12 months, with no prepayment penalty.
Why Indiana calls us for repiping
We've been a trusted choice since 1974 — over 50 years of family-owned plumbing service across Indiana. Our techs are CSLB-licensed (#1098234), background-checked, and complete an internal 12-week training program before rolling on calls alone.
Our repiping carries a 10-year workmanship guarantee — separate from any manufacturer warranty on the parts themselves. If the repiping we performed fails because of how we did it, we come back and fix it free for a full decade. Appliances and fixtures we install are backed by their full manufacturer warranty, and the parts and accessories we fit carry standard 1–5 year warranties by item.
We quote repiping on honest scope: no unnecessary up-sell, salaried (never commissioned) technicians, and a transparent diagnostic so you see exactly what we see — including the parts still in good shape. If a repair is the right call we say so; if replacement is the better long-term economics, we say that. The flat-rate repiping quote is written and good for 30 days.
Our repiping service area
We provide repiping throughout Indiana, with fast coverage in every major Indiana metro.
Outside Indiana? Our Repiping nationwide page is the national hub for this service in all 50 states.
Reach times for repiping vary by traffic and time of day, so we quote an accurate ETA when you call — and the dispatch line routes straight to an on-call technician, no voicemail in between.
Frequently asked about repiping
Top questions homeowners searching for Repiping near me ask us:
Do you handle permits and patching?
Yes — we pull the permit, schedule the municipal inspection, and patch and texture every access point we open. Final paint is typically the homeowner's, and we leave the walls ready for it.
How long does a repipe take?
A typical single-story home is repiped in 2–3 days: one day to run and tie in the new lines and pass pressure test, and the patching and inspection following. Two-story and larger homes run 3–5 days. Water is usually restored each evening.
What financing is available?
Synchrony 0% APR for 12 months on qualifying projects. Longer terms at low fixed rates are also available. Fast approval, no prepayment penalty, and it can cover a water heater or softener added in the same project.
PEX or copper — which should I choose?
PEX-A is lower cost, freeze-tolerant, corrosion-proof, and has fewer in-wall joints; copper is rigid, proven, and preferred for exposed runs and specific code situations. Most whole-home repipes today use PEX-A, but we'll price both.
What's the project day like?
We lay protection, open the minimum access points, route the new PEX or copper, connect every fixture, pressure-test the system, and schedule the inspection. Then we patch and texture the access holes so the walls look right again. Most homeowners stay in the home throughout.